Spectrum-controls 1769sc-HART Modules Instrukcja Użytkownika Strona 36
- Strona / 186
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Compact IO™ Isolated HART Analog Input Module
User's Manual 0300215-03 Rev. A
4-8
The table below gives a brief description of each data type.
Table 4-2 (User Defined Data Type Descriptions)
User Defined Data Type Description
GetDeviceInfoStructure Defines the structure of the HART data returned by the
module when the module specific command, Get
Device Information, is sent to module.
1
If4ihMessage This data type defines the structure for tags used to
send messages to and from the module using the paging
scheme.
1
If4ihPassThruMsg Defines the structure for tags used to send HART pass
through messages to and from the module.
1
Packet0 Defines the data structure for HART packet 0. HART
packet zero contains device information for the
connected HART device.
1
Packet1 Defines the data structure for HART packet 1. HART
packet 1 is used to display the four dynamic variables
for the selected HART device.
1
Packet2 Defines the data structure for HART packet 2. HART
packet 2 is used to display the slot variables for the
connected HART device.
1
Packet3 Defines the data structure for HART packet 3. HART
packet 3 displays the ASCII message for the connected
HART device.
1
Packet4 Defines the data structure for HART packet 4. HART
packet 4 contains the extended status for the connected
HART device.
1
Section 4.4
Project Tags
The project tags were created to simplify the configuration of the module. Some of the
tags defined in the sample project utilize the user defined data types described in the
previous section.
The user defined tags from the controller scope should be copied to your project before
the tags contained in the individual program sections. Open the controller tags on the
sample project and select the edit tags mode. Grab the tags you want to copy by using
the left mouse button and dragging. See figure below.
1
Refer to Chapter 6 for more details.
2
Refer to Chapter 7 for more details.
- Compact™ I/O 1
- Isolated HART 1
- Analog Module 1
- Table of Contents 3
- Preface 7
- Conventions 8
- Used in This 8
- Chapter 1 9
- Module Overview 9
- Do No t Remov e RTB Un der 10
- Power Unless Area is Non 10
- Hazardous 10
- Section 1.5 11
- System 11
- Overview 11
- 1.5.1 System Operation 11
- Section 1.6 12
- Module 12
- Operation 12
- Chapter 2 13
- Quick Start for Experienced 13
- Chapter 3 19
- Installation and Wiring 19
- 3.3.3 Remove Power 21
- 3.3.4 Selecting a Location 21
- Section 3.4 22
- System Assembly 22
- Section 3.5 23
- Mounting 23
- 3.5.1 Minimum Spacing 23
- 3.5.2 Panel Mounting 23
- 3.5.3 DIN Rail Mounting 24
- 3.7.2 Terminal Door Label 26
- 3.7.5 Wiring the Module 27
- 3.7.6 Wiring Diagram 28
- 3.7.7 Calibration 28
- Chapter 4 29
- Configuring the IF4IH for 29
- CompactLogix Using 29
- RSLogix 5000 29
- Section 4.2 33
- The Add-On 33
- Profile 33
- Section 4.4 36
- Project Tags 36
- Project 38
- Chapter 5 41
- Configuring the IF4IH for a 41
- MicroLogix 1500 Using 41
- RSLogix 500 41
- Section 5.2 42
- Configuring 42
- 1500 System 42
- Section 5.3 46
- Using the 46
- Ladder Sample 46
- Chapter 6 51
- Module Data, Status, and 51
- Channel Configuration 51
- Section 6.4 55
- Configuration 55
- Raw/Proportional Data 62
- Engineering Units 62
- Scaled-for-PID 62
- Percent Range 62
- 6.4.9 Channel X 64
- 6.4.10 Channel X 64
- 6.5.8 Reserved (Words 24…45) 66
- Section 6.6 67
- Determining 67
- Effective 67
- Resolution 67
- Section 6.7 68
- Update Time 68
- Chapter 7 69
- Enabling and Using HART on 69
- Table 7-1 (HART Packet 0) 73
- Table 7-2 (HART Packet 1) 74
- Figure 7-4 (Packet Ladder) 77
- 7.2.3 Packet Interval 78
- Section 7.3 79
- Sending 79
- Messages 79
- 7.3.3 Processing a Message 81
- Figure 7-6 Sending Message 82
- Figure 7-8a (Message Ladder) 84
- Figure 7-8b 85
- Figure 7-8c 86
- Figure 7-8d 87
- Figure 7-8e 88
- Figure 7-8f 89
- Figure 7-8g 90
- Figure 7-8h 91
- Figure 7-8i 92
- Figure 7-8j 93
- Figure 7-8m 95
- Figure 7-8n 96
- Figure 7-8o 97
- Section 7.4 98
- Module Specific 98
- Commands 98
- Attention 103
- Figure 7-10b 107
- Figure 7-10c 108
- Figure 7-10d 109
- Figure 7-10e 110
- Section 7.5 111
- HART Protocol 111
- 7.5.1 Message Format 111
- Chapter 8 117
- Programming Examples 117
- Figure 8-4b 121
- 8.2.1 MAIN Routine 123
- 8.2.2 PACKETS Routine 124
- Figure 8-6b 125
- Figure 8-6c 126
- 8.2.3 MSG_TO_MOD Routine 127
- Figure 8-7b 128
- Figure 8-7c 129
- Figure 8-7d 130
- Figure 8-7e 131
- Figure 8-7f 132
- Figure 8-7g 133
- Figure 8-7h 134
- Figure 8-7i 135
- Figure 8-7j 136
- Figure 8-7k 137
- Figure 8-7l 138
- Figure 8-7m 139
- Figure 8-7n 140
- Figure 8-7o 141
- Figure 8-7p 142
- Figure 8-7q 143
- 8.2.4 SRC_CHECK Routine 144
- Figure 8-8b 145
- 8.2.5 DEST_CHECKSUM Routine 146
- Figure 8-9b 147
- 8.2.6 HART_MSG Routine 148
- Figure 8-10b 149
- Figure 8-10c 150
- Figure 8-10d 151
- Figure 8-10e 152
- Figure 8-10f 153
- Figure 8-10g 154
- Figure 8-10h 155
- Figure 8-10i 156
- Figure 8-10j 157
- Figure 8-10k 158
- 8.2.7 WORD_BYTE Routine 159
- Figure 8-11b 160
- Figure 8-11c 161
- 8.2.8 HART_CHECK Routine 162
- Figure 8-12b 163
- 8.2.9 BYTE_WORD Routine 164
- Figure 8-13b 165
- Chapter 9 167
- Diagnostics and 167
- Troubleshooting 167
- 1514131211109876543210 169
- 0000000000000000 169
- Value Bits 11 170
- Description 170
- Section 9.8 171
- Inhibit Function 171
- Appendix A 173
- Module Specifications 173
- Section A.2 174
- Environmental 174
- Specifications 174
- Appendix B 177
- HART Universal and Common 177
- Practice Commands 177
- Wire Size · 3-9 183
- Wiring Diagram · 3-10 183
- Wiring Guidlines · 2-3 183
- Getting Technical 185
- Assistance 185
- Declaration of 185
- Conformity 185
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Spectrum-controls 1769sc-HART Modules
(176 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji